Spear-Top Double Swing Gate with Side Panels | Fabrication Drawings
Palisade double swing driveway gate between fixed side panels. Leaves and panels carry vertical spears with a choice of tips (crimped, arrowhead, pressed point, ball, finial, fleur-de-lis or fishtail), optional puppy-picket heights and rings or a band, so the run reads as one palisade broken only by the gate posts. Equal or custom leaf split, an optional centre post, left, right or both panels with optional outer posts, and the double gate hardware: lock, striker, drop bolt, stop strip, gate stops, a Swing Plan sheet and a Hardware Details sheet, each off until you switch it on. Level ground.
Configure Spear-Top Double Swing Gate with Side Panels dimensions and download professional A4 PDF fabrication drawings with orthographic views and dimension lines. No CAD software needed. Sub-millimetre precision from a true 3D solid model.
Key facts
Specifications
| Parameter | Range |
|---|---|
| Overall Width | 1,000 mm to 30,000 mm |
| Gate Width | 500 mm to 30,000 mm |
| Clear Opening Height | 600 mm to 6,000 mm |
| Gap Below Gate | 0 mm to 1,000 mm |
| Leaf Split | Equal, Custom |
| Left Leaf Width | 150 mm to 12,000 mm |
| LHS Tolerance | 5 mm to 80 mm |
| RHS Tolerance | 5 mm to 80 mm |
| Meeting Tolerance | 3 mm to 80 mm |
| Centre Post LHS Tolerance | 3 mm to 80 mm |
| Centre Post RHS Tolerance | 3 mm to 80 mm |
| Corner Joint | Mitre, Butt |
| Stile Extension Above Top Rail | 0 mm to 30,000 mm |
| Hinge Type | Not shown, Weld-on butt hinge, Bolt-on plate hinge, Pivot bearing (top and bottom), Weld-on bullet hinge, Adjustable eye-bolt hinge, 180 degree hinge, Face-fixed self-closing hinge |
| Bearing Unit | Custom (enter sizes below), UCP207 pillow block (2 bolt, 35 mm bore), UCF207 square flange (4 bolt, 35 mm bore) |
| Hinge Positions | Near the ends, Evenly spaced, Custom heights |
| Hinge 1 Height | 0 mm to 6,000 mm |
| Hinge 2 Height | 0 mm to 6,000 mm |
| Hinge 3 Height | 0 mm to 6,000 mm |
| Hinge 4 Height | 0 mm to 6,000 mm |
| Hinge Plate Width | 1 mm to 3,000 mm |
| Hinge Plate Depth | 1 mm to 15,000 mm |
| Hinge Plate Thickness | 1 mm to 5,000 mm |
| Hinge Bolt Hole Diameter | 1 mm to 2,500 mm |
| Hinge Bolt Inset | 0 mm to 6,000 mm |
| Bearing Boss Diameter | 1 mm to 12,000 mm |
| Bearing Pin Diameter | 1 mm to 6,000 mm |
| Bearing Pin Length | 1 mm to 3,000 mm |
| Hinge Plate Offset | 0 mm to 6,000 mm |
| Bullet Hinge Length | 60 mm to 250 mm |
| Bullet Hinge Diameter | 12 mm to 40 mm |
| Eye Bolt Thread | M12, M16, M20 |
| Eye Bolt Reach | 40 mm to 120 mm |
| 180 Hinge Length | 50 mm to 250 mm |
| 180 Hinge Knuckle | 10 mm to 40 mm |
| Hinge Fitted Side | Back of the gate, Front of the gate (opens outwards) |
| Self-Closing Hinge Length | 50 mm to 300 mm |
| Self-Closing Hinge Leaf Width | 20 mm to 100 mm |
| Self-Closing Hinge Knuckle | 10 mm to 50 mm |
| Hinge Pin Offset | 0 mm to 120 mm |
| Mid Rail 1 Orientation | Horizontal, Vertical, Diagonal |
| Mid Rail 1 Position | 0 mm to 50,000 mm |
| Mid Rail 1 Recess | 0 mm to 500 mm |
| Mid Rail 2 Orientation | Horizontal, Vertical, Diagonal |
| Mid Rail 2 Position | 0 mm to 50,000 mm |
| Mid Rail 2 Recess | 0 mm to 500 mm |
| Mid Rail 3 Orientation | Horizontal, Vertical, Diagonal |
| Mid Rail 3 Position | 0 mm to 50,000 mm |
| Mid Rail 3 Recess | 0 mm to 500 mm |
| Mid Rail 4 Orientation | Horizontal, Vertical, Diagonal |
| Mid Rail 4 Position | 0 mm to 50,000 mm |
| Mid Rail 4 Recess | 0 mm to 500 mm |
| Mid Rail 5 Orientation | Horizontal, Vertical, Diagonal |
| Mid Rail 5 Position | 0 mm to 50,000 mm |
| Mid Rail 5 Recess | 0 mm to 500 mm |
| Mid Rail 6 Orientation | Horizontal, Vertical, Diagonal |
| Mid Rail 6 Position | 0 mm to 50,000 mm |
| Mid Rail 6 Recess | 0 mm to 500 mm |
| Left Post Material | Steel (galvanised), Aluminium, Stainless steel (304/316) |
| Left Post Attachment | Concrete into Ground, Bolted to Side Wall, Footplate |
| Left Post Concrete Depth | 0 mm to 3,000 mm |
| Left Post Footplate Position | Toe left, Toe right, Toe in, Toe out, Centre, Top left, Top right, Top centre (as saved) |
| Right Post Material | Steel (galvanised), Aluminium, Stainless steel (304/316) |
| Right Post Attachment | Concrete into Ground, Bolted to Side Wall, Footplate |
| Right Post Concrete Depth | 0 mm to 3,000 mm |
| Right Post Footplate Position | Toe left, Toe right, Toe in, Toe out, Centre, Top left, Top right, Top centre (as saved) |
| Footplate Width | 1 mm to 5,000 mm |
| Footplate Depth | 1 mm to 5,000 mm |
| Footplate Thickness | 1 mm to 500 mm |
| Left Post Hole Ø | 1 mm to 3,000 mm |
| Left Post Hole Edge Inset | 0 mm to 12,000 mm |
| Right Post Hole Ø | 1 mm to 3,000 mm |
| Right Post Hole Edge Inset | 0 mm to 12,000 mm |
| Left Post Footplate Width | 1 mm to 5,000 mm |
| Left Post Footplate Depth | 1 mm to 5,000 mm |
| Left Post Footplate Thickness | 1 mm to 500 mm |
| Right Post Footplate Width | 1 mm to 5,000 mm |
| Right Post Footplate Depth | 1 mm to 5,000 mm |
| Right Post Footplate Thickness | 1 mm to 500 mm |
| Centre Post Material | Steel (galvanised), Aluminium, Stainless steel (304/316) |
| Centre Post Attachment | Concrete into Ground, Footplate |
| Centre Post Concrete Depth | 0 mm to 3,000 mm |
| Centre Post Footplate Position | Toe left, Toe right, Toe in, Toe out, Centre, Top left, Top right, Top centre (as saved) |
| Centre Post Footplate Width | 1 mm to 5,000 mm |
| Centre Post Footplate Depth | 1 mm to 5,000 mm |
| Centre Post Footplate Thickness | 1 mm to 500 mm |
| Centre Post Hole Ø | 1 mm to 3,000 mm |
| Centre Post Hole Edge Inset | 0 mm to 12,000 mm |
| Spear Distribution | Fixed Gap, Number of Spears |
| Gap Between Spears | 0 mm to 10,000 mm |
| Offset From Each Stile | 0 mm to 10,000 mm |
| Spear Top Treatment | Through Top Rail (protrudes above), Flush with Top Rail |
| Spear Top Protrusion | 0 mm to 1,000 mm |
| Spear Bottom Treatment | Cut Into Bottom Rail (sits on top), Flush with Bottom Rail, Through Bottom Rail (protrudes below) |
| Spear Bottom Protrusion | 0 mm to 1,000 mm |
| Spear Mounting | Face-Fixed (front of frame), Pierce Frame (centred through rails) |
| Tip Style | Crimped Pyramid, Cast Arrowhead, Pressed Point, Ball Top, Ball Finial, Fleur-de-Lis, Fishtail, Plain Cut End |
| Tip Height (Inside Protrusion) | 0 mm to 1,000 mm |
| Ball Diameter | 1 mm to 500 mm |
| Finial Collar Height | 0 mm to 500 mm |
| Fleur-de-Lis Width | 1 mm to 1,000 mm |
| Fleur-de-Lis Style | Classic French, Gothic Lance, Florentine, Heraldic, Victorian Spearhead, Scrolled, Laser Plate |
| Fleur-de-Lis Made As | Cast head (bought in), Flat plate (cut in the shop) |
| Cap Plate Thickness | 0 mm to 500 mm |
| Arrowhead Base Width | 1 mm to 1,000 mm |
| Arrowhead Base Depth | 1 mm to 1,000 mm |
| Arrowhead Collar Height | 0 mm to 500 mm |
| Arrowhead Collar Overhang | 0 mm to 200 mm |
| Pressed Point Width | 1 mm to 1,000 mm |
| Pressed Point Thickness | 1 mm to 1,000 mm |
| Pressed Point Shoulder | 0 mm to 2,000 mm |
| Spear Height Pattern | All Same Height, Alternating, Puppy Pickets |
| Short Spear Protrusion | 0 mm to 1,000 mm |
| Short Spear Tip | Same as Tall Spears, Plain Cut End |
| Rings and Bands | None, Rings Between Spears, Second Rail Band |
| Ring Outer Diameter | 1 mm to 2,000 mm |
| Ring Bar Diameter | 1 mm to 100 mm |
| Ring Height Above Top Rail | 0 mm to 5,000 mm |
| Band Bar Size | 1 mm to 500 mm |
| Band Height Above Top Rail | 0 mm to 5,000 mm |
| Rail Hole Clearance | 0 mm to 100 mm |
| Jockey Wheel Position | 0 mm to 12,000 mm |
| Jockey Wheel Diameter | 1 mm to 10,000 mm |
| Pocket Notch Length | 1 mm to 10,000 mm |
| Pocket Notch Depth | 1 mm to 15,000 mm |
| Pocket Housing Length | 1 mm to 10,000 mm |
| Pocket Housing Height | 1 mm to 15,000 mm |
| Pocket Slot Width | 1 mm to 12,000 mm |
| Leaves Open | In, toward the property, Out, toward the street |
| Lock Type | Not shown, Lever handle, Ball handle, Mortice lock, D-latch, Slide bolt, Other |
| Lock Box Width | 40 mm to 300 mm |
| Lock Box Height | 80 mm to 400 mm |
| Lock Box Centre Height | 500 mm to 1,600 mm |
| Catch Plate Position | Top of gate, Bottom of gate, Custom height |
| Height from Ground | 100 mm to 2,400 mm |
| Plate Width | 30 mm to 200 mm |
| Plate Height | 30 mm to 200 mm |
| Plate Thickness | 3 mm to 12 mm |
| Plate Overhang | Centred on the edge, Custom |
| Overhang Past Edge | 0 mm to 300 mm |
| Plate Material | Stainless steel, Aluminium, Galvanised steel |
| Drop Bolt | Not shown, Drop bolt |
| Bolt Rod Diameter | 10 mm to 32 mm |
| Bolt Length | 200 mm to 1,200 mm |
| Bolt Guide Length | 80 mm to 500 mm |
| Bolt Throw | 50 mm to 300 mm |
| Engagement Into Ground | 20 mm to 200 mm |
| Bolt Fixing | Welded on, Bolted on |
| Rod Stand-off | 10 mm to 80 mm |
| Bolt On | Passive leaf only, Both leaves |
| Rod From Meeting Edge | 0 mm to 300 mm |
| Socket Depth | 30 mm to 200 mm |
| Socket Diameter | 12 mm to 60 mm |
| Strip Welded To | Passive leaf, Active leaf |
| Strip Width | 20 mm to 100 mm |
| Strip Thickness | 3 mm to 12 mm |
| Lap Onto Other Leaf | 10 mm to 40 mm |
| Centre Stop Width | 60 mm to 300 mm |
| Centre Stop Depth | 60 mm to 300 mm |
| Centre Stop Height | 20 mm to 200 mm |
| Centre Stop Plate Thickness | 3 mm to 25 mm |
| Stop Off Centre | 0 mm to 200 mm |
| Open Stops | Not shown, Ground stop, Hold-back catch |
| Open Stop For | Both leaves, Active leaf only, Passive leaf only |
| Stop From Free End | 0 mm to 3,000 mm |
| Open Stop Base | 50 mm to 300 mm |
| Open Stop Height | 30 mm to 400 mm |
| Open Stop Diameter | 20 mm to 150 mm |
| Panel Configuration | Left Only, Right Only, Both Sides |
| Panel Gap Below | 0 mm to 1,000 mm |
| Wall Inset | 0 mm to 250 mm |
| Panel Mid Rail Position | Match gate mid rail, Centre of panel |
| Left Outer Post Material | Steel (galvanised), Aluminium, Stainless steel (304/316) |
| Left Outer Post Attachment | Concrete into Ground, Bolted to Side Wall, Footplate |
| Left Outer Post Concrete Depth | 0 mm to 3,000 mm |
| Left Outer Footplate Position | Toe left, Toe right, Toe in, Toe out, Centre, Top left, Top right, Top centre (as saved) |
| Right Outer Post Material | Steel (galvanised), Aluminium, Stainless steel (304/316) |
| Right Outer Post Attachment | Concrete into Ground, Bolted to Side Wall, Footplate |
| Right Outer Post Concrete Depth | 0 mm to 3,000 mm |
| Right Outer Footplate Position | Toe left, Toe right, Toe in, Toe out, Centre, Top left, Top right, Top centre (as saved) |
| Left Outer Post Hole Ø | 1 mm to 3,000 mm |
| Left Outer Post Hole Edge Inset | 0 mm to 12,000 mm |
| Right Outer Post Hole Ø | 1 mm to 3,000 mm |
| Right Outer Post Hole Edge Inset | 0 mm to 12,000 mm |
| Left Outer Post Footplate Width | 1 mm to 5,000 mm |
| Left Outer Post Footplate Depth | 1 mm to 5,000 mm |
| Left Outer Post Footplate Thickness | 1 mm to 500 mm |
| Right Outer Post Footplate Width | 1 mm to 5,000 mm |
| Right Outer Post Footplate Depth | 1 mm to 5,000 mm |
| Right Outer Post Footplate Thickness | 1 mm to 500 mm |
| Left Panel Outer End Fixing | Fixed to the wall, Fixing tabs |
| Right Panel Outer End Fixing | Fixed to the wall, Fixing tabs |
| Panel Tab Type | Flat tab in line with the rail, Vertical plate beside the rail, End plate on the wall |
| Panel Tab Direction | Up, Down, Left up, right down, Left down, right up |
| Panel Tab Length | 1 mm to 15,000 mm |
| Panel Plate Width | 1 mm to 2,500 mm |
| Panel Tab Thickness | 1 mm to 500 mm |
| Panel Tab Position on the Rail | Centred on the rail, Flush with the front face, Flush with the back face |
| Drawing Rules | Current rules, As saved before October 2026 |
Frequently Asked Questions
What opening widths does the Spear-Top Double Swing Gate with Side Panels support?
The Spear-Top Double Swing Gate with Side Panels accepts opening widths from 500 mm to 30,000 mm. Enter your exact site measurement and the engine recomputes all frame members, battens or slats, and dimension lines to match.
What heights can the Spear-Top Double Swing Gate with Side Panels be?
Heights range from 600 mm to 6,000 mm. Left and right heights can differ to accommodate raked or sloped ground. The drawing recomputes automatically for any height within the range.
What do I get in the drawing pack?
Each drawing pack is an A4 PDF with orthographic views (front elevation, side elevation, top view, and isometric), full dimension lines, extension lines, and a professional title block. You also get a live 3D preview in the browser and optional STEP file export for CAD software.
Can I use this drawing for fabrication?
Yes. Dimensions are computed to sub-millimetre precision from a true 3D solid model, not approximated from a template. Print the PDF at actual size, hand it to your fabricator, and build from it. Change any input and the entire drawing regenerates in about 60 seconds.
How long does it take to generate a Spear-Top Double Swing Gate with Side Panels drawing?
Around 60 seconds end-to-end. Geometry computation runs server-side in a CadQuery process with a 30-second per-request timeout; PDF rendering and download account for the rest. If you change a dimension, regeneration takes the same ~60 seconds — there is no manual redrafting step.
Can I save and reload my dimensions for the Spear-Top Double Swing Gate with Side Panels?
Yes. The free Explorer tier keeps 1 saved drawing, so you always have somewhere to land between visits. Fabricator saves every drawing you make and reloads the configurator in one click, so you can revise a quote, regenerate a clean PDF, or branch a design for a similar customer without re-typing dimensions.
References & technology
Category: Gates. Tags: gate, double-swing, driveway, spear, palisade, side-panels, fabrication. Geometry built with CadQuery on the OCCT (OpenCascade Technology) kernel — the same geometry foundation used in FreeCAD and a number of commercial CAD packages. Drawings are orthographic projections of the computed 3D solid; no view is sketched or scaled from a template.
Related terminology in the CAD60 fabrication glossary: see orthographic view, dimension line, title block, RHS, and aluminium.
