Ornamental Single Swing Gate | Fabrication Drawings
Wrought-iron style single swing gate: one full-width leaf of vertical bars carrying fleur-de-lis, collars, baskets or twisted lengths from the ornament library. Add scrolls bent from flat bar and a ring or scroll frieze under the top rail. Posts, hinges, a catch plate and a jockey wheel are set in the configurator.
Configure Ornamental Single Swing Gate dimensions and download professional A4 PDF fabrication drawings with orthographic views and dimension lines. No CAD software needed. Sub-millimetre precision from a true 3D solid model.
Key facts
Specifications
| Parameter | Range |
|---|---|
| Clear Opening Width | 200 mm to 30,000 mm |
| Clear Opening Height | 300 mm to 6,000 mm |
| Gap Below Gate | 0 mm to 1,000 mm |
| Corner Joint | Mitre, Butt |
| Left Post Material | Steel (galvanised), Aluminium, Stainless steel (304/316) |
| Left Post Attachment | Concrete into Ground, Bolted to Side Wall, Footplate |
| Left Post Concrete Depth | 0 mm to 3,000 mm |
| Left Post Footplate Position | Toe left, Toe right, Toe in, Toe out, Centre, Top left, Top right, Top centre (as saved) |
| Right Post Material | Steel (galvanised), Aluminium, Stainless steel (304/316) |
| Right Post Attachment | Concrete into Ground, Bolted to Side Wall, Footplate |
| Right Post Concrete Depth | 0 mm to 3,000 mm |
| Right Post Footplate Position | Toe left, Toe right, Toe in, Toe out, Centre, Top left, Top right, Top centre (as saved) |
| Footplate Width | 1 mm to 5,000 mm |
| Footplate Depth | 1 mm to 5,000 mm |
| Footplate Thickness | 1 mm to 500 mm |
| Left Post Hole Ø | 1 mm to 3,000 mm |
| Left Post Hole Edge Inset | 0 mm to 12,000 mm |
| Right Post Hole Ø | 1 mm to 3,000 mm |
| Right Post Hole Edge Inset | 0 mm to 12,000 mm |
| Left Post Footplate Width | 1 mm to 5,000 mm |
| Left Post Footplate Depth | 1 mm to 5,000 mm |
| Left Post Footplate Thickness | 1 mm to 500 mm |
| Right Post Footplate Width | 1 mm to 5,000 mm |
| Right Post Footplate Depth | 1 mm to 5,000 mm |
| Right Post Footplate Thickness | 1 mm to 500 mm |
| Largest Gap Between Bars | 1 mm to 5,000 mm |
| Gap At Each End | 0 mm to 10,000 mm |
| Ornament 1 | None, Fleur-de-lis: Classic French, Fleur-de-lis: Gothic Lance, Fleur-de-lis: Florentine, Fleur-de-lis: Heraldic, Fleur-de-lis: Victorian Spearhead, Fleur-de-lis: Scrolled, Fleur-de-lis: Laser Plate, Collar, Bush, Knuckle, Basket, Fine Basket, Twist |
| Ornament 1 On | Every bar, Every second bar, Every third bar, Centre bar only, End bars only |
| Ornament 1 Height Above Bottom Rail | 0 mm to 20,000 mm |
| Ornament 1 Size | 0 mm to 5,000 mm |
| Ornament 2 | None, Fleur-de-lis: Classic French, Fleur-de-lis: Gothic Lance, Fleur-de-lis: Florentine, Fleur-de-lis: Heraldic, Fleur-de-lis: Victorian Spearhead, Fleur-de-lis: Scrolled, Fleur-de-lis: Laser Plate, Collar, Bush, Knuckle, Basket, Fine Basket, Twist |
| Ornament 2 On | Every bar, Every second bar, Every third bar, Centre bar only, End bars only |
| Ornament 2 Height Above Bottom Rail | 0 mm to 20,000 mm |
| Ornament 2 Size | 0 mm to 5,000 mm |
| Ornament 3 | None, Fleur-de-lis: Classic French, Fleur-de-lis: Gothic Lance, Fleur-de-lis: Florentine, Fleur-de-lis: Heraldic, Fleur-de-lis: Victorian Spearhead, Fleur-de-lis: Scrolled, Fleur-de-lis: Laser Plate, Collar, Bush, Knuckle, Basket, Fine Basket, Twist |
| Ornament 3 On | Every bar, Every second bar, Every third bar, Centre bar only, End bars only |
| Ornament 3 Height Above Bottom Rail | 0 mm to 20,000 mm |
| Ornament 3 Size | 0 mm to 5,000 mm |
| Fleur-de-lis Made As | Cast piece (bought in), Flat plate (cut in the shop) |
| Fleur-de-lis Thickness | 1 mm to 200 mm |
| Scrolls | None, C scrolls, S scrolls, Heart, Lyre |
| Scroll Layout | Either side of a bar, Between two bars |
| Scrolls On | Every bar, Every second bar, Every third bar, Centre bar only, End bars only |
| Scroll Height | 0 mm to 20,000 mm |
| Scroll Height Above Bottom Rail | 0 mm to 20,000 mm |
| Scroll Width | 0 mm to 5,000 mm |
| Scroll Ends | Snub (rounded), Plain cut, Fishtail, Penny (round disc) |
| Frieze | None, Rings, S scrolls |
| Frieze Height | 1 mm to 5,000 mm |
| Frieze Ring Bar | 1 mm to 100 mm |
| Hinge Tolerance | 0 mm to 500 mm |
| Latch Tolerance | 0 mm to 500 mm |
| Lock Type | No Lock/Handle, Lever Handle Lock, Ball Handle Lock, Mortice Lock, Lokklatch, Other |
| Lockbox Width | 1 mm to 6,000 mm |
| Lockbox Height | 1 mm to 6,000 mm |
| Lockbox Height from Ground | 0 mm to 6,000 mm |
| Lock Height from Ground | 500 mm to 1,600 mm |
| Hinge Type | Not shown, Weld-on butt hinge, Bolt-on plate hinge, Pivot bearing (top and bottom), Weld-on bullet hinge, Adjustable eye-bolt hinge, 180 degree hinge |
| Bearing Unit | Custom (enter sizes below), UCP207 pillow block (2 bolt, 35 mm bore), UCF207 square flange (4 bolt, 35 mm bore) |
| Hinge Positions | Near the ends, Evenly spaced, Custom heights |
| Hinge 1 Height | 0 mm to 6,000 mm |
| Hinge 2 Height | 0 mm to 6,000 mm |
| Hinge 3 Height | 0 mm to 6,000 mm |
| Hinge 4 Height | 0 mm to 6,000 mm |
| Hinge Plate Width | 1 mm to 3,000 mm |
| Hinge Plate Depth | 1 mm to 15,000 mm |
| Hinge Plate Thickness | 1 mm to 5,000 mm |
| Hinge Bolt Hole Diameter | 1 mm to 2,500 mm |
| Hinge Bolt Inset | 0 mm to 6,000 mm |
| Bearing Boss Diameter | 1 mm to 12,000 mm |
| Bearing Pin Diameter | 1 mm to 6,000 mm |
| Bearing Pin Length | 1 mm to 3,000 mm |
| Hinge Plate Offset | 0 mm to 6,000 mm |
| Bullet Hinge Length | 60 mm to 250 mm |
| Bullet Hinge Diameter | 12 mm to 40 mm |
| Eye Bolt Thread | M12, M16, M20 |
| Eye Bolt Reach | 40 mm to 120 mm |
| 180 Hinge Length | 50 mm to 250 mm |
| 180 Hinge Knuckle | 10 mm to 40 mm |
| Hinge Pin Offset | 0 mm to 120 mm |
| Weld Plate To | Latch Stile (gate), Latch Post (frame) |
| Catch Plate Face | Back (property side), Front (street side) |
| Catch Plate Position | Top of gate, Bottom of gate, Custom height |
| Height from Ground | 0 mm to 6,000 mm |
| Plate Width | 1 mm to 12,000 mm |
| Plate Height | 1 mm to 6,000 mm |
| Plate Thickness | 1 mm to 600 mm |
| Plate Overhang | Centred on the edge, Custom |
| Overhang Past Edge | 0 mm to 5,000 mm |
| Plate Material | Stainless steel, Aluminium, Galvanised steel |
| Jockey Wheel Position | 0 mm to 12,000 mm |
| Jockey Wheel Diameter | 1 mm to 10,000 mm |
| Pocket Notch Length | 1 mm to 10,000 mm |
| Pocket Notch Depth | 1 mm to 15,000 mm |
| Pocket Housing Length | 1 mm to 10,000 mm |
| Pocket Housing Height | 1 mm to 15,000 mm |
| Pocket Slot Width | 1 mm to 12,000 mm |
| Drawing Rules | Current rules, As saved before October 2026 |
Frequently Asked Questions
What opening widths does the Ornamental Single Swing Gate support?
The Ornamental Single Swing Gate accepts opening widths from 200 mm to 30,000 mm. Enter your exact site measurement and the engine recomputes all frame members, battens or slats, and dimension lines to match.
What heights can the Ornamental Single Swing Gate be?
Heights range from 300 mm to 6,000 mm. Left and right heights can differ to accommodate raked or sloped ground. The drawing recomputes automatically for any height within the range.
What do I get in the drawing pack?
Each drawing pack is an A4 PDF with orthographic views (front elevation, side elevation, top view, and isometric), full dimension lines, extension lines, and a professional title block. You also get a live 3D preview in the browser and optional STEP file export for CAD software.
Can I use this drawing for fabrication?
Yes. Dimensions are computed to sub-millimetre precision from a true 3D solid model, not approximated from a template. Print the PDF at actual size, hand it to your fabricator, and build from it. Change any input and the entire drawing regenerates in about 60 seconds.
How long does it take to generate a Ornamental Single Swing Gate drawing?
Around 60 seconds end-to-end. Geometry computation runs server-side in a CadQuery process with a 30-second per-request timeout; PDF rendering and download account for the rest. If you change a dimension, regeneration takes the same ~60 seconds — there is no manual redrafting step.
Can I save and reload my dimensions for the Ornamental Single Swing Gate?
Yes. The free Explorer tier keeps 1 saved drawing, so you always have somewhere to land between visits. Fabricator saves every drawing you make and reloads the configurator in one click, so you can revise a quote, regenerate a clean PDF, or branch a design for a similar customer without re-typing dimensions.
References & technology
Category: Gates. Tags: gate, single-swing, swing, driveway, ornamental, wrought-iron, fleur-de-lis, scrollwork, decorative, fabrication. Geometry built with CadQuery on the OCCT (OpenCascade Technology) kernel — the same geometry foundation used in FreeCAD and a number of commercial CAD packages. Drawings are orthographic projections of the computed 3D solid; no view is sketched or scaled from a template.
Related terminology in the CAD60 fabrication glossary: see orthographic view, dimension line, title block, RHS, and aluminium.
